What was originally planned as a simple cylinder head test on the 312 dyno mule ended up being a test that ultimately involved over two dozen different sets of cylinder heads. While part of this testing was a precursor to determining which pair of heads were to be used for an extensive exhaust system test, the remainder of the cylinder head test was to answer some questions about the significance of milling and porting on some of the various heads. This test saw no fewer than thirty different head changes on the engine as some of those pairs of heads were reworked differently between the tests or were reinstalled as part of the base-lining that was being performed to insure that the engine performance was remaining constant.Continue reading “Cylinder Head Testing – Part 1”
With the basics of the cylinder head test being introduced in YBM issue #153, part II of this article will concentrate more heavily on the more pertinent details of the various heads that were tested.Continue reading “Cylinder Head Testing – Part 2”
When the question came up as to how well some of the various exhaust and header designs perform on the Ford Y-Block family of engines, the 312 dyno mule was again put to work in doing an extensive exhaust system test. Twenty-four different exhaust systems ranging from single exhaust to stepped headers were tested with each system being tried in a variety of configurations. Where possible, the different exhaust systems were also tested with and without mufflers and a variety of head-pipe lengths. When mufflers were used, they were sized according to the pipe size going into them which required having a variety of chambered mufflers on hand for this test. Except in the case of where the headers used for the 2010 EMC competition were used, mufflers were a deterrent for making additional power. While there are mufflers out there that are not a detriment for power production, those simply were not on hand for this test.Continue reading “Ford Y-Block Exhaust Testing”
The Rollmaster true roller timing sets have been available for a number of years now for the Ford Y-Block family of engines. These have been a big plus for those engine builders that go to the extra effort of degreeing in the camshafts as the lower crankshaft gear is keyed for nine different camshaft positions. Before these Rollmaster timing sets came to market, degreeing in the camshafts on the Y involved offset keys or broaching new keyway slots in the crankshaft or camshaft timing gears. The offset keys were always questionable strength wise regardless if the valve spring pressures were increased or not. The practice of broaching new keyway slots in the gears is not an exact science when it comes to getting the new keyway in the exact ‘right’ location. The Rollmaster timing sets eliminates those prior difficulties.
When David Church acquired a 1955 Ford Customline two door sedan, it was found that it was originally ordered as a law enforcement car with the P code 292 and a three speed standard transmission. A little back tracking finds that the car was purchased new in North Carolina and when found by David, still had the 1967 North Carolina license plates on it but was now sitting in a South Carolina field. It had been well over 40 years since the car had been last registered and state inspected. Although that car had been sitting in a field for a number of years, a bit of fuel poured into the ‘Teapot’ 4V carburetor and a battery boost gets it started. It drives itself up and onto a trailer for the trip back to Mississippi. The odometer is showing 60K miles but when looking at suspension, pedal wear, and general oil and grease build up at various parts of the car, the assumption is the car has 160K miles instead. More time elapses and now the car is undergoing a complete restoration including an engine rebuild. The engine rebuild is where I come into the picture.
This is the article recently published in The Y-Block Magazine issue #146 (May-June 2018) authored by Joe Craine.
Part of the blueprinting process during any engine buildup will include degreeing in the camshaft. This operation is performed to insure the camshaft is phased or installed at the desired position in relation to the piston sitting at TDC. While degreeing in the camshaft during its installation may seem to be an activity reserved just for the race engines, the fact remains that it’s just as important on the daily driver applications as it is for high performance engines.
Most camshaft timing sets for the Ford Y family of engines (239/256/272/292/312) requires that there be twelve pins between the timing marks on the sprockets and for those marks to be on the oil filter side of the engine when doing the initial chain installation. The exception here is that this only applies to Y engines that actually use a timing chain and does not apply to right hand or reverse rotation marine engines that use a gear to gear setup. While the Y is not the only engine to use the pin or link count between gear marks to time the camshaft, most V8 engine families simply align the timing marks on the cam gear and crank gear with the centerline of the engine. Due to the infrequency of engine manufacturers using the pin or link count for camshaft timing, it does leave the door open for mishaps by those not familiar with this.
Although there were a multitude of Ford 272 Y-Block engines used in both cars and trucks, they are pretty much disregarded as the basis for a high performance build and for that matter, as a replacement engine when a 292 or 312 is available instead. While building a high performance 272 Y has been on the ‘like to do’ list for awhile, it has been a hard sell when the larger Y engines simply make those higher power numbers much easier to come by. That all changed recently when a customer wanted to use the original 272 block from their 1956 Ford pickup as the basis for a new engine in that same truck. In this instance, they wanted modern performance upgrades applied to it including a pair of Mummert aluminum heads.